Logo

P3464 Engine Trouble Code

P3464 Engine

When you check engine light came on code P3464 the reason should be . However your vehicle's manufacturer may have a different definition for the P3464 OBD-II Diagnostic Powertrain (P) Trouble Code. So you should chech it on our car models.

P3464 code can be about changing a broken oxygen sensor can lead to a busted catalytic convertor which can cost upwards of $1,300. Taking your vehicle into a service shop will cost you around $300 depending on the vehicle. But, an oxygen sensor is easy to replace on many vehicles and is detailed in the owner's manual PDF or in our website. If you know where this sensor is located, you only have to unclip the old oxygen sensor and replace it with a new sensor. Regardless of how you approach it, you should get this fixed right away.

P3464 Code Meaning :

P
OBD-II Diagnostic Powertrain (P) Trouble Code For Engine
3
Ignition System Or Misfire
4
Fuel Temperature Sensor B Circuit Range/Performance
6
Injection Pump Fuel Metering Control 'A' High (Cam/Rotor/Injector)
4
Clutch Position Sensor Circuit Malfunction

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

P3464 OBD-II Diagnostic Powertrain (P) Trouble Code Description

P3464 engine trouble code is about Clutch Position Sensor Circuit Malfunction. Fuel Temperature Sensor B Circuit Range/Performance and Injection Pump Fuel Metering Control 'A' High (Cam/Rotor/Injector) causes most of code P3464.

Reason For P3464 Code

The reason of P3464 OBD-II Engine Trouble Code is Fuel Temperature Sensor B Circuit Range/Performance.

P3464 the main thing to check is to verify the operation of the VCT solenoid in the engine. You're looking for a sticking or stuck VCt solenoid valve caused by contamination. Refer to vehicle specific service repair manual to perform component tests for the VCT unit.

How To Repair P3464 Code

Before starting let's see P3464 repairing process steps:

  • Qualified technicians will begin by using a scan tool to access P3464 code stored in the ECU.
  • Technicians will note P3464 code present and any freeze frame data associated with them.
  • After all, if you sure the engine trouble is finished, the code will be cleared.

The transmission uses hydraulic pressure, controlled by solenoids, which are controlled by the PCM, to shift gears and provide torque converter lockup. The PCM calculates the necessary amount of pressure at any given time to optimize vehicle operation.

If nothing is done to repair the persistent P3464 code, the ECU will put the vehicle into a limp mode. This mode limits the top speed and reduces engine power greatly to protect the engine.

Sometimes P3464 code comes with P346400 code.

Diagnosis Of Engine Error OBD Code P3464

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a P3464 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the P3464 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.

All Engine Trouble Codes

All engine trouble codes with P, U, B and C engine codes.

Code Search

Please fill the "Code Box" to find engine fault code.

Example: 0140

Car Models :

Please select your car.

How To Read Engine Codes ?

Ways to read engine trouble codes.

How To Clear Check Engine Lights ?

Ways to clear check engine light on car panel.

Check Engine Light Dictionary

Ways to clear check engine light on car panel.